nblocks:n-pro-00
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
nblocks:n-pro-00 [2020/02/07 10:41] faizan [Table] |
nblocks:n-pro-00 [2022/01/13 06:05] (current) engineer [Getting started] |
||
|---|---|---|---|
| Line 81: | Line 81: | ||
| n-PRO-00 is a **HOST** board with two Hirose DF30-series 60-pin low profile connectors at bottom side, following the [[nblocks:nproformfactor|n-Blocks PRO form factor]].\\ | n-PRO-00 is a **HOST** board with two Hirose DF30-series 60-pin low profile connectors at bottom side, following the [[nblocks:nproformfactor|n-Blocks PRO form factor]].\\ | ||
| <WRAP centeralign>{{:nblocks:n-pro-00-02.jpg?400|}}</WRAP> | <WRAP centeralign>{{:nblocks:n-pro-00-02.jpg?400|}}</WRAP> | ||
| - | + | \\ | |
| - | + | <WRAP centeralign>{{:nblocks:n-pro-00-nbusa.jpg|}}</WRAP> | |
| - | ** to be updated ** | + | \\ |
| + | <WRAP centeralign>{{:nblocks:n-pro-00-nbusb.jpg|}} </WRAP> | ||
| \\ | \\ | ||
| Line 116: | Line 117: | ||
| ==USB Serial Port== | ==USB Serial Port== | ||
| * To use the debug serial port of the LPC11U35 to emulate a serial port over USB see the example [[https://developer.mbed.org/handbook/USBSerial|here.]] | * To use the debug serial port of the LPC11U35 to emulate a serial port over USB see the example [[https://developer.mbed.org/handbook/USBSerial|here.]] | ||
| + | |||
| + | |||
| + | ===Using n-PRO-00 as drag n drop programming tool=== | ||
| + | The 10-pin JTAG connector available on board, is to program a target ARM-Cortex board (Not the n-PRO-00 LPC11U35 Microcontroller). \\ | ||
| \\ | \\ | ||
| + | <WRAP centeralign>{{:nblocks:n-pro-00-prog01.jpg?600|}} </WRAP> | ||
| + | \\ | ||
| + | To be able to use the n-PRO-00 as programming tool we first need to program it with one of the binaries below:\\ | ||
| + | Once the CMSIS-DAP firmware is programmed to n-PRO-00 LPC11U35 Flash memory, it appears as a USB disk.\\ | ||
| + | Now we are ready to drag n drop the binary for the target board to the USB disk.\\ | ||
| + | ==LPC1768/LPC812== | ||
| + | *[[https://developer.mbed.org/users/chalikias/code/mbed-HDK/| LPC11U35-Firmware for communicating with LPC1768]] (Does not create virtual serial port) | ||
| + | *[[https://os.mbed.com/platforms/SWDAP-LPC11U35/ |SWDAP-LPC11U35 NXP LPC1768 PREBUILD IMAGE]] (Creates a virtual serial port) | ||
| + | |||
| + | ==LPC1114FN28== | ||
| + | *[[https://developer.mbed.org/teams/Switch-Science/wiki/Firmware-LPC1114FN28| Firmware LPC1114FN28]] (Firmware to use n-DAP with the non-SMD LPC1114FN28 DIP-28) | ||
| + | |||
| + | ==nRF51822== | ||
| + | *[[http://www.seeedstudio.com/wiki/Arch_BLE| Seeed studio wiki Arch BLE]] | ||
| + | *[[http://www.seeedstudio.com/wiki/File:Lpc11u35_nrf51822_if_mbed.bin.zip| Seeed studio wiki File:Lpc11u35 nrf51822 if mbed.bin.zip]] | ||
| + | *[[https://os.mbed.com/platforms/Y5-LPC11U35-MBUG/#bootloader-for-ble-mbug |Bootloader for BLE mbug]] | ||
| + | |||
| + | ==NXP K64F== | ||
| + | *[[https://os.mbed.com/platforms/SWDAP-LPC11U35/NXP K64F]] | ||
| + | *[[https://os.mbed.com/media/uploads/chris/lpc11u35_swdap_k64f_if_crc.bin bin]] | ||
| + | |||
| + | ==CMSIS-DAP Interface Firmware== | ||
| + | * [[https://docs.mbed.com/docs/handbook/en/latest/CMSIS/Interface_Firmware/ |CMSIS-DAP Interface Firmware]] | ||
| + | |||
| + | |||
| + | |||
| + | \\ | ||
| =====References===== | =====References===== | ||
nblocks/n-pro-00.1581090074.txt.gz · Last modified: 2020/02/07 10:41 by faizan
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
