nblocks:n-pro-10
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
nblocks:n-pro-10 [2020/02/05 11:37] faizan [Getting started] |
nblocks:n-pro-10 [2020/02/07 12:09] (current) faizan |
||
|---|---|---|---|
| Line 15: | Line 15: | ||
| <WRAP centeralign> | <WRAP centeralign> | ||
| LPC1769 full breakout in n-PRO modular form factor</WRAP> | LPC1769 full breakout in n-PRO modular form factor</WRAP> | ||
| - | | License | GPL 2.0 | | + | | License | GPL 2.0 | |
| - | | Status | Tested | | + | | Status | Tested | |
| - | | Buy at: | | | + | | Buy at: | | |
| - | | Categories | | | + | | Categories | | |
| - | | Hardware repo | [[https://bitbucket.org/nimbus_it/n-pro-10|Bitbucket]] | | + | | Hardware repo | [[https://bitbucket.org/nimbus_it/pcba-n-pro-10|Bitbucket]] | |
| - | | Firmware repo | [[https://bitbucket.org/nimbus_it/n-pro-10|Bitbucket]] | | + | | Firmware repo | | |
| </WRAP> | </WRAP> | ||
| Line 112: | Line 112: | ||
| ===== Getting started===== | ===== Getting started===== | ||
| - | ===Blinky with mbed compiler=== | ||
| * Connect the board to the battery or power supply. | * Connect the board to the battery or power supply. | ||
| * Press the reset button, green LED will indicate that you have power connected. | * Press the reset button, green LED will indicate that you have power connected. | ||
| - | * After a few seconds a mass storage device named CRP_DISABLED will show up on your computer | ||
| - | |||
| - | {{:nblocks:n-pro-00-04.png?400|}} | ||
| * Select target on mbed online compiler | * Select target on mbed online compiler | ||
| - | * Create a blinky program like below | + | * Create a blinky program like below. Compile and it will get downloaded. |
| <code c++> | <code c++> | ||
| #include "mbed.h" | #include "mbed.h" | ||
| Line 134: | Line 130: | ||
| } | } | ||
| </code> | </code> | ||
| - | * Delete the existing firmware.bin file, and replace it with the .bin file you downloaded from the mbed compiler. | + | *Connect the board to j-link. |
| + | {{:nblocks:n-pro-10-p1.jpg?400|}} | ||
| + | * Open J-Flash Lite, select the device. | ||
| + | {{:nblocks:n-pro-10-p0.jpg?600|}} | ||
| + | * Select the bin file downloaded from mbed compiler. | ||
| + | {{:nblocks:n-pro-10-p2.jpg?600|}} | ||
| + | * Click on Program device | ||
| + | {{:nblocks:n-pro-10-p3.jpg?400|}} | ||
| * Press RESET, and the board will now be running your code. | * Press RESET, and the board will now be running your code. | ||
| Line 141: | Line 144: | ||
| \\ | \\ | ||
| \\ | \\ | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| =====References===== | =====References===== | ||
nblocks/n-pro-10.1580920679.txt.gz · Last modified: 2020/02/05 11:37 by faizan
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
