nblocks:n-pro-12pin
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
nblocks:n-pro-12pin [2020/02/17 15:05] engineer |
nblocks:n-pro-12pin [2020/02/21 06:55] (current) faizan |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| <WRAP right 220px nblock round :en> | <WRAP right 220px nblock round :en> | ||
| <WRAP centeralign>//**n-PRO-12PIN**// </WRAP> | <WRAP centeralign>//**n-PRO-12PIN**// </WRAP> | ||
| - | {{:nblocks:n-pro-dap-09.jpg}} | + | {{:nblocks:N-PRO-12-PIN-02.JPG}} |
| <WRAP centeralign> | <WRAP centeralign> | ||
| n-PRO-12PIN</WRAP> | n-PRO-12PIN</WRAP> | ||
| Line 18: | Line 18: | ||
| [[nblocks:n-PRO-12PIN|n-PRO-12PIN]] A 120 pins n-PRO n-Block can be used with this 12 pin adapter-breakout, for low pin-count applications, using a perforated board and simple soldering/wiring | [[nblocks:n-PRO-12PIN|n-PRO-12PIN]] A 120 pins n-PRO n-Block can be used with this 12 pin adapter-breakout, for low pin-count applications, using a perforated board and simple soldering/wiring | ||
| - | <WRAP centeralign>{{:nblocks:n-pro-dap-02.jpg?300|}}</WRAP> | + | <WRAP centeralign>{{:nblocks:N-PRO-12-PIN-01.JPG?300|}}</WRAP> |
| ===== Overview===== | ===== Overview===== | ||
| <poem> | <poem> | ||
| - | [[nblocks:n-PRO-DAP|n-PRO-DAP]] board can facilitate USB drag and drop firmware programming of ARM based CPU boards. It comes with the NXP Semiconductor's LPC11U35 MCU which belongs to the enhanced line of LPC11U3x, ARM-Cortex M0 based, low-cost 32-bit MCU family. The LPC11U35 operate at CPU frequencies of up to 50 MHz and brings unparalleled design flexibility and seamless integration to today’s prototyping and development solutions. The board provides access to the CPUs, ADC, UART and I2C pins which allow the user to use it as a stand alone development board when programmed with custom firmware. | + | [[nblocks:n-PRO-12PIN|n-PRO-12PIN]] board |
| - | + | ||
| - | + | ||
| - | The n-PRO-DAP (if flashed with a binary image) behaves as a USB to JTAG/SWD bridge between the computer and target's debug access port, using the ARM CMSIS DAP for user friendly programming and debugging. It enables firmware development for n-Blocks boards using the ARM mbed platform and can also be used with industry standard tools such as Keil and IAR. | + | |
| - | </poem> | + | |
| + | <WRAP centeralign>{{nblocks:n-pro-12-pin-nbusa.jpg|}}</WRAP> | ||
| \\ | \\ | ||
| + | <WRAP centeralign>{{nblocks:n-pro-12-pin-nbusb.jpg|}}</WRAP> | ||
| \\ | \\ | ||
| + | |||
| + | |||
| + | |||
nblocks/n-pro-12pin.1581969943.txt.gz · Last modified: 2020/02/17 15:05 by engineer
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
