Differences

This shows you the differences between two versions of the page.

--- nblocks:n-pro-20 [2019/07/31 05:00]
faizan
+++ nblocks:n-pro-20 [2020/02/17 15:24] (current)
engineer
@@ Line 1: / Line 1: @@
 ======n-PRO-20======
 ~~CLOSETOC~~
-<WRAP  no_pdf >
-**this page is work in progress**
-  *<todo  >better perspective image  </todo>
-  *<todo  >add bootloader connector  </todo>
-  *<todo  >add sudo-bed programing example, demonstrating its simplicity </todo>
-~~TODOLIST ns:nblocks:n-pro-20 completed:no~~
-</WRAP>
 <WRAP right 220px nblock round :en>
 <WRAP centeralign>//**n-PRO-20**// </WRAP>
-{{n-pro-20-03.png}}
+{{:nblocks:n-pro-20-09b.jpg?400|}}
 <WRAP centeralign>
 ESP32-WROOM  in n-PRO modular form factor</WRAP>
-| License        | GPL 2.0 |
+| License        | GPL 2.0                                                      |
-| Status         | Tested |
+| Status         | Tested                                                       |
-| Buy at:        |   |
+| Buy at:        |                                                              |
-| Categories     |  |
+| Categories     |                                                              |
-| Hardware repo  | [[https://bitbucket.org/nimbus_it/n-dap|Bitbucket]] |
+| Hardware repo  | [[https://bitbucket.org/nimbus_it/pcba-n-pro-20|Bitbucket]]  |
-| Firmware repo  | [[https://bitbucket.org/nimbus_it/n-dap|Bitbucket]] |
+| Firmware repo  |                                                              |
 </WRAP>
-n-PRO-20 is an ultra low-power, high performance and secure development board from the n-Blocks family, in the [[nblocks:proformfactor|n-Blocks PRO form factor]], designed for Internet-of-Things gateway applications.
+n-PRO-20 is an ultra low-power, high performance and secure development board from the n-Blocks family. It is available in the [[nblocks:proformfactor|n-Blocks PRO form factor]], designed for Internet-of-Things gateway applications.
-<WRAP centeralign>{{:nblocks:n-pro-20-00.PNG?400|}}</WRAP>
+<WRAP centeralign>{{:nblocks:n-pro-20-01.jpg?300|}}</WRAP>
 =====Overview=====
 <poem>
-[[nblocks:n-ble|n-PRO-20]] is a development board based on Espressif ESP32-WROOM. The WiFi, Bluetooth Classic and BLE make it a great choice to build anything connected. The module is all-around: using Wi-Fi allows a large physical range and direct connection to the Internet through a Wi-Fi router, while using Bluetooth allows the user to conveniently connect to the phone or broadcast low energy beacons for its detection.The built-in hardware accelerator enables secure code storage and securely connecting to the Internet with TLS (SSL). Data rate of up to 150 Mbps are supported, and 20 dBm output power at the antenna ensures the widest physical range. The sleep current is less than 5 µA, which makes it suitable for battery powered and wearable electronics applications.
+[[nblocks:n-ble|n-PRO-20]] is a development board based on Espressif ESP32-WROOM. The WiFi, Bluetooth Classic and BLE make it a great choice to build anything connected. The Wi-Fi allows a large physical range and direct connection to the Internet through a Wi-Fi router. While using Bluetooth, the user can conveniently connect to the phone or broadcast low energy beacons for its detection.
+The built-in hardware accelerator enables secure code storage and securely connecting to the Internet with TLS (SSL). Data rate of up to 150 Mbps are supported, and 20 dBm output power at the antenna ensures the widest physical range. The sleep current is less than 5 µA, which makes it suitable for battery powered and wearable electronics applications.
-[[nblocks:n-dap|n-DAP]] can be connected in piggyback style to provide [[nblocks:mbed enable|mbed-enable]].
 </poem>
@@ Line 78: / Line 67: @@
-=====Main Features Of The Board=====
+===== n-PRO-20 Features=====
+<WRAP left 600px  :en>
   * Simple and Low Power
   * Standard [[nblocks:nblocks-pinout|n-Blocks pinout]]
   * Miniature Li-Ion battery connector (optional)
+</WRAP>
   * Custom firmware development via SDK
   * Download and write firmware via host
@@ Line 90: / Line 82: @@
 =====Board Pinout=====
- The board has 2 x50 pin SMD connectors, following the [[nblocks:nproformfactor|n-Blocks PRO form factor]].\\
+ n-PRO-20 is a **HOST** board with four Hirose DF30-series 60-pin low profile connectors at bottom side, following the [[nblocks:nproformfactor|n-Blocks PRO form factor]].\\
-<WRAP centeralign>{{:nblocks:n-pro-20-01.PNG?250|}} {{:nblocks:n-pro-20-02.PNG?250|}}</WRAP>
+<WRAP centeralign>{{nblocks:n-pro-20-02.jpg?300|}}</WRAP>
+<WRAP centeralign>{{:nblocks:n-pro-20-nbusa.jpg|}}</WRAP>
+\\
+<WRAP centeralign>{{:nblocks:n-pro-20-nbusb.jpg|}} </WRAP>
+\\
+<WRAP centeralign>{{:nblocks:n-pro-20-nbusc.jpg|}}</WRAP>
 \\
+<WRAP centeralign>{{:nblocks:n-pro-20-nbusd.jpg|}}</WRAP>
 \\
 \\
-===== Geting started=====
+===== Getting started=====
 To get started with the board you need:
   * PC loaded with either Windows, Linux or Mac operating system
@@ Line 212: / Line 206: @@
   * Save the sketch. Verify and Upload.
 **NOTE: You might have to hold the Boot button during upload to avoid error.**
-\\
-\\
 \\
@@ Line 221: / Line 212: @@
 =====Flash Memory Programming=====
+** to be updated**
 \\
 \\
 ====Programming with sudo-bed====
-\\
-\\
-=====USE-CASE examples=====
@@ Line 236: / Line 222: @@
+=====References=====
+  * [[https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.pdf|ESP32 Datasheet]]
+  * https://docs.espressif.com/projects/esp-idf/en/latest/get-started/
 =====Related articles in this Wiki=====
-  *[[ ]]
+  *[[nblocks:n-ble|n-PRO-20]]
 {{tag> RF CPU nblock BLE  nsensorRF}}

nblocksWiki

User Tools

Site Tools

Differences

Page Tools