nblocks:n-pro-30
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
nblocks:n-pro-30 [2020/02/04 05:11] faizan |
nblocks:n-pro-30 [2020/02/07 10:39] (current) faizan [Table] |
||
|---|---|---|---|
| Line 6: | Line 6: | ||
| <WRAP centeralign> | <WRAP centeralign> | ||
| n-PRO-30</WRAP> | n-PRO-30</WRAP> | ||
| - | | License | GPL 2.0 | | + | | License | GPL 2.0 | |
| - | | Status | Tested-Blink | | + | | Status | Tested-Blink | |
| - | | Buy at: | | | + | | Buy at: | | |
| - | | Categories | | | + | | Categories | | |
| - | | Hardware repo | [[https://bitbucket.org/nimbus_it/n-pro-30|Bitbucket]] | | + | | Hardware repo | [[https://bitbucket.org/nimbus_it/pcba-n-pro-30|Bitbucket]] | |
| - | | Firmware repo | [[https://bitbucket.org/nimbus_it/n-pro-30|Bitbucket]] | | + | | Firmware repo | | |
| </WRAP> | </WRAP> | ||
| Line 19: | Line 19: | ||
| ===== Overview===== | ===== Overview===== | ||
| <poem> | <poem> | ||
| - | [[nblocks:n-ble|n-PRO-30]] is a simple Bluetooth Low Energy board based on Nordic nRF58232. It can be combined with another RF module like [[nblocks:n-lora|n-LoRa]] for combined Long Range and BLE applications or with a [[nblocks:n-node24|n-Node24]] for BLE/802.2.15 networking. In addition, up to three [[nblocks:n-sensor|n-Sensor]] boards can be installed. It can be used as a standalone BLE sensor beacon, or as a base processor for Lora or 802.15.4 node with multi-sensing and BLE for commissioning/parameterising at Ultra Low Power. The board supports the standard Nordic Software Development Tool-chain using Keil, IAR and GCC. It also supports ARM mbed tool-chain for rapid prototyping and development using mbed’s IDE and tool-chain with an extensive range of open-source software libraries. | + | [[nblocks:n-ble|n-PRO-30]] is a simple Bluetooth Low Energy board based on Nordic nRF58232. It consists of temperature/humidity sensor, acceleration sensor and ambient light sensor which can be used to collect data and transmit it over bluetooth. The board supports the standard Nordic Software Development Tool-chain using Keil, IAR and GCC. It also supports ARM mbed tool-chain for rapid prototyping and development using mbed’s IDE and tool-chain with an extensive range of open-source software libraries. |
| </poem> | </poem> | ||
| Line 95: | Line 95: | ||
| <WRAP centeralign>{{:nblocks:n-pro-30-nbusa.jpg|}}</WRAP> | <WRAP centeralign>{{:nblocks:n-pro-30-nbusa.jpg|}}</WRAP> | ||
| + | |||
| + | <WRAP centeralign>{{:nblocks:n-pro-30-nbusb.jpg|}}</WRAP> | ||
| <WRAP centeralign>{{:nblocks:n-pro-30-nbusc.jpg|}}</WRAP> | <WRAP centeralign>{{:nblocks:n-pro-30-nbusc.jpg|}}</WRAP> | ||
| Line 108: | Line 110: | ||
| ===== Getting started===== | ===== Getting started===== | ||
| - | |||
| ===Blinky using Nordic SDK=== | ===Blinky using Nordic SDK=== | ||
| *Follow the first part of this [[https://devzone.nordicsemi.com/tutorials/7/|tutorial]] | *Follow the first part of this [[https://devzone.nordicsemi.com/tutorials/7/|tutorial]] | ||
nblocks/n-pro-30.1580811089.txt.gz · Last modified: 2020/02/04 05:11 by faizan
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
