nblocks:n-pro-dap
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
nblocks:n-pro-dap [2020/02/18 05:25] faizan |
nblocks:n-pro-dap [2020/02/27 07:43] (current) engineer |
||
|---|---|---|---|
| Line 23: | Line 23: | ||
| ===== Overview===== | ===== Overview===== | ||
| - | <poem> | + | [[nblocks:n-PRO-DAP|n-PRO-DAP]] board can facilitate USB drag and drop firmware programming of ARM based CPU boards. It comes with the NXP Semiconductor's LPC11U35 MCU which belongs to the enhanced line of LPC11U3x, ARM-Cortex M0 based, low-cost 32-bit MCU family. The LPC11U35 operate at CPU frequencies of up to 50 MHz and brings unparalleled design flexibility and seamless integration to today’s prototyping and development solutions. The low profile connectors allows the user to connect peripheral boards as and when required. |
| - | [[nblocks:n-PRO-DAP|n-PRO-DAP]] board can facilitate USB drag and drop firmware programming of ARM based CPU boards. It comes with the NXP Semiconductor's LPC11U35 MCU which belongs to the enhanced line of LPC11U3x, ARM-Cortex M0 based, low-cost 32-bit MCU family. The LPC11U35 operate at CPU frequencies of up to 50 MHz and brings unparalleled design flexibility and seamless integration to today’s prototyping and development solutions. The board provides access to the CPUs, ADC, UART and I2C pins which allow the user to use it as a stand alone development board when programmed with custom firmware. | + | |
| ===DAP interface=== | ===DAP interface=== | ||
| - | The n-DAP (if flashed with a binary image) behaves as a USB to JTAG/SWD bridge between the computer and target's debug access port, using the ARM CMSIS DAP for user friendly programming and debugging. It enables firmware development for n-Blocks boards using the ARM mbed platform and can also be used with industry standard tools such as Keil and IAR. | + | The n-PRO-DAP (if flashed with a binary image) behaves as a USB to JTAG/SWD bridge between the computer and target's debug access port, using the ARM CMSIS DAP for user friendly programming and debugging. It enables firmware development for n-Blocks boards using the ARM mbed platform and can also be used with industry standard tools such as Keil and IAR. |
| The CMSIS-DAP Interface Firmware provides: | The CMSIS-DAP Interface Firmware provides: | ||
| Line 72: | Line 72: | ||
| =====Main Features Of The Board===== | =====Main Features Of The Board===== | ||
| <WRAP left 600px :en> | <WRAP left 600px :en> | ||
| - | * Small size | + | * Three User LEDs |
| + | * USB 2.0 FS with Micro connector | ||
| * Drag-and-drop programming | * Drag-and-drop programming | ||
| * SWD/JTAG connector | * SWD/JTAG connector | ||
| - | * 5V USB or 4.5-5.5V supply | + | |
| | | ||
| </WRAP> | </WRAP> | ||
| - | * Built-in USB drag 'n' drop FLASH programmer | + | * Built-in USB drag 'n' drop FLASH programmer |
| * Reset and Bootloader enable push-buttons | * Reset and Bootloader enable push-buttons | ||
| * Cortex debug interface connector | * Cortex debug interface connector | ||
| + | * 5V USB or 4.5-5.5V supply | ||
| Line 87: | Line 89: | ||
| =====Board Pinout===== | =====Board Pinout===== | ||
| - | **to be updated** | ||
| <WRAP centeralign>{{:nblocks:n-pro-dap-01.jpg?300|}}</WRAP> | <WRAP centeralign>{{:nblocks:n-pro-dap-01.jpg?300|}}</WRAP> | ||
| + | \\ | ||
| + | <WRAP centeralign>{{:nblocks:n-pro-dap-nbusa.jpg|}}</WRAP> | ||
| + | \\ | ||
| + | <WRAP centeralign>{{:nblocks:n-pro-dap-nbusb.jpg|}} </WRAP> | ||
| + | \\ | ||
| + | <WRAP centeralign>{{:nblocks:n-pro-dap-nbusc.jpg|}} </WRAP> | ||
| + | |||
| + | \\ | ||
| + | <WRAP centeralign>{{:nblocks:n-pro-dap-nbusd.jpg|}} </WRAP> | ||
| + | |||
| \\ | \\ | ||
| Line 100: | Line 111: | ||
| \\ | \\ | ||
| - | ===== Geting started===== | + | ===== Getting started===== |
| - | ===Blinky with mbed compiler=== | + | ===Programming n-PRO-10 using n-PRO-DAP=== |
| * Plug the USB cable to the n-PRO-DAP board. | * Plug the USB cable to the n-PRO-DAP board. | ||
| Line 125: | Line 136: | ||
| </code> | </code> | ||
| * Download the bin file from the mbed compiler. | * Download the bin file from the mbed compiler. | ||
| - | * Drag and drop the file on the DAPLINK | + | * Drag and drop the file on the DAPLINK. |
| * Press RESET, and the n-PRO-10 board will now be running your code. | * Press RESET, and the n-PRO-10 board will now be running your code. | ||
nblocks/n-pro-dap.1582021554.txt.gz · Last modified: 2020/02/18 05:25 by faizan
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
