nblocks:n-pro-wurx
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
nblocks:n-pro-wurx [2019/10/29 13:07] faizan |
nblocks:n-pro-wurx [2020/09/19 17:58] (current) engineer |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | **in progress** | ||
| ====== n-PRO-WuRx====== | ====== n-PRO-WuRx====== | ||
| ~~CLOSETOC~~ | ~~CLOSETOC~~ | ||
| <WRAP right 220px nblock round :en> | <WRAP right 220px nblock round :en> | ||
| - | <WRAP centeralign>//**n-PRO-30**// </WRAP> | + | <WRAP centeralign>//**n-PRO-WuRx**// </WRAP> |
| {{:nblocks:n-pro-wurx-03.jpg}} | {{:nblocks:n-pro-wurx-03.jpg}} | ||
| <WRAP centeralign> | <WRAP centeralign> | ||
| - | n-PRO-30</WRAP> | + | n-PRO-WuRx</WRAP> |
| | License | GPL 2.0 | | | License | GPL 2.0 | | ||
| - | | Status | Tested | | + | | Status | Design in progress| |
| | Buy at: | | | | Buy at: | | | ||
| | Categories | | | | Categories | | | ||
| - | | Hardware repo | [[https://bitbucket.org/nimbus_it/n-pro-30|Bitbucket]] | | + | | Hardware repo | [[https://bitbucket.org/nimbus_it/n-PRO-WuRx|Bitbucket]] | |
| - | | Firmware repo | [[https://bitbucket.org/nimbus_it/n-pro-30|Bitbucket]] | | + | | Firmware repo | [[https://bitbucket.org/nimbus_it/n-PRO-WuRx|Bitbucket]] | |
| </WRAP> | </WRAP> | ||
| - | n-PRO-WuRx is a 3D Low Frequency Wakeup Receiver targeting access control and RFID applications. The [[nblocks:formfactor|n-Blocks pro form factor]] makes it makes it perfectly suitable for seamless integration. | + | n-PRO-WuRx is a 3D Low Frequency Wakeup Receiver targeting access control and RFID applications. The [[nblocks:formfactor|n-Blocks pro form factor]] makes it perfectly suitable for seamless integration. |
| <WRAP centeralign>{{:nblocks:n-pro-wurx-01.jpg?300|}}</WRAP> | <WRAP centeralign>{{:nblocks:n-pro-wurx-01.jpg?300|}}</WRAP> | ||
| \\ | \\ | ||
| ===== Overview===== | ===== Overview===== | ||
| <poem> | <poem> | ||
| - | [[nblocks:n-ble|n-PRO-WuRx]] shows the main features of AS3933. These include three dimensional wake up mode detection, error wake-up window readout, which may be used to measure current consumption in different operating modes, as well as SPI communication and data output measurement access. The detection efficiency can be observed immediately by using the 125 kHz wake up transmitter. | + | [[nblocks:n-ble|n-PRO-WuRx]] is based on AS3933. It is capable of generating a wake-up signal upon detection of a data signal, ranging between 15-150 KHz carrier frequency. The programmable features of AS3933 allows the user to retain consistent wake-up generation for longer distances. It can operate using one, two, or three active channels. Each channel supports a programmable data rate and Manchester decoding. |
| </poem> | </poem> | ||
| Line 32: | Line 33: | ||
| \\ | \\ | ||
| - | ===== n-PRO-30 Features ===== | + | ===== n-PRO-WuRx Features ===== |
| <WRAP left 600px :en> | <WRAP left 600px :en> | ||
| * 3-channel ASK wake-up receiver | * 3-channel ASK wake-up receiver | ||
| Line 55: | Line 56: | ||
| =====Board Pinout projected to Top side===== | =====Board Pinout projected to Top side===== | ||
| - | n-PRO-WuRx is a **PERIPHERAL** board with 4 x 60 pin MOLEX SLIMSTACK connectors at bottom side, following the [[nblocks:nproformfactor|n-Blocks PRO form factor]].\\ | + | n-PRO-WuRx is a **PERIPHERAL** board four Hirose DF30-series 60-pin low profile connectors at bottom side, following the [[nblocks:nproformfactor|n-Blocks PRO form factor]].\\ |
| <WRAP centeralign>{{:nblocks:n-pro-wurx-02.jpg?300|}}</WRAP> | <WRAP centeralign>{{:nblocks:n-pro-wurx-02.jpg?300|}}</WRAP> | ||
nblocks/n-pro-wurx.1572368846.txt.gz · Last modified: 2019/10/29 13:07 by faizan
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
