nblocks:ni-pro-3dp
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
nblocks:ni-pro-3dp [2021/02/20 14:18] engineer |
nblocks:ni-pro-3dp [2021/02/21 05:19] (current) engineer |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ======ni-PRO-3DP====== | + | ======n-PRO-3DP====== |
| ~~CLOSETOC~~ | ~~CLOSETOC~~ | ||
| <WRAP no_pdf > | <WRAP no_pdf > | ||
| Line 29: | Line 29: | ||
| ===== - Overview===== | ===== - Overview===== | ||
| <poem> | <poem> | ||
| - | [[nblocks:ni-PRO-3DP|ni-PRO-3DP]] is a motion controll board that is integrated with the mighty function of n-Blocks-PRO. The most attractive feature of this board is the streamlined interfaces, which help us to avoid the unnecessary troubles in handling the multiple motors, compact layout design allow us to integrate all required functionality available in small space and last but not least is the versatile mounting provision is available which support nearly all sort of applications. | + | [[nblocks:ni-PRO-3DP|ni-PRO-3DP]] is a motion controll board that is integrated with the mighty function of n-Blocks-PRO. The most attractive feature of this board is the streamlined interfaces, which help us to avoid the unnecessary troubles in handling the multiple motors, heaters, fans, end-stop switches, thermistors and sensors. Compact layout design allow us to integrate all required functionality in small space. The versatile screw-terminals, support simple setup for all sort of stepping-motor/motion/power applications. |
| Line 43: | Line 43: | ||
| =====Main Features Of The Board===== | =====Main Features Of The Board===== | ||
| <WRAP left 600px :en> | <WRAP left 600px :en> | ||
| - | * Any processor can be integrated by plugging into the connectors | + | * Different processor can be integrated by plugging nBlocksPRO boards for LPC1768, STM32F103,F401,... |
| - | * Super quiet A4988 stepper driverse | + | * Many options of StepsticK stepping-motor drivers can be used, including Super quiet Silent-Stepsticks |
| * Convenient for users to DIY and secondary development | * Convenient for users to DIY and secondary development | ||
| * Four Hirose DF30-series 60-pin low profile connectors | * Four Hirose DF30-series 60-pin low profile connectors | ||
| - | * n-DAP can be integrated | + | * n-DAP can be integrated for convenient firmware development/Debugging |
| - | * Modular, event-driven design, allowing to add functionality easily | + | * Modular, event-driven design, allowing to add functionality easily, when used with nBlocksStudio |
| + | * Smoothieware compatibility | ||
| </WRAP> | </WRAP> | ||
| * Easy to use and configure. | * Easy to use and configure. | ||
| * Smooth, jerk-free motion and enabling higher speeds | * Smooth, jerk-free motion and enabling higher speeds | ||
| * Can be used for CNC milling, laser cutting, and 3D printing | * Can be used for CNC milling, laser cutting, and 3D printing | ||
| - | * Opensource/hardware all-included controller board | ||
| * SD-Card support for configuration and executing G-code | * SD-Card support for configuration and executing G-code | ||
| * Composite USB Mass Storage + Serial interface to host | * Composite USB Mass Storage + Serial interface to host | ||
nblocks/ni-pro-3dp.1613848724.txt.gz · Last modified: 2021/02/20 14:18 by engineer
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
