====== n-PRO-SEN1======

~~CLOSETOC~~
<WRAP right 220px nblock round :en>
<WRAP centeralign>//**n-PRO-SEN1**// </WRAP>
{{:nblocks:n-pro-sen1-09.jpg}}
<WRAP centeralign>
n-PRO-s1</WRAP>
| License        | GPL 2.0                                                        |
| Status         | Tested                                                         |
| Buy at:        |                                                                |
| Categories     |                                                                |
| Hardware repo  | [[https://bitbucket.org/nimbus_it/pcba-n-pro-sen1|Bitbucket]]  |
| Firmware repo  |                                                                |
</WRAP>

n-PRO-S1 is an environmental sensor board, in the standard [[nblocks:formfactor|n-Blocks pro form factor]].
<WRAP centeralign>{{:nblocks:n-pro-s1-02.jpg?400|}}</WRAP>

===== Overview=====
<poem>
[[nblocks:n-pro-sen1|n-PRO-S1]] is designed around the MAX44009 **ambient light** sensor, the LIS2DTW12  **motion and temperature** sensor, the BME860 **atmospheric pressure and VOC** sensor and the SI7006 **Temperature/Humidity** Sensor.The board can be used to monitor the environment conditions, and store or transmit the data to a remote system for further processing. The [[nblocks:PERIPHERAL|n-PRO PERIPHERAL]] connectors pinout allow [[nblocks:n-pro-sen1|n-PRO-S1]] to be connected to any [[nblocks:HOST|n-PRO HOST]]  board to add additional functionality. It is simple to just plug and get started with sensor applications immediately.
</poem>
\\
\\
===== MAX44009 Features ====
<WRAP left 600px  :en>
  * Wide 0.045 Lux to 188,000 Lux Range
  * Small, 2mm x 2mm x 0.6mm UTDFN-Opto 
  * VCC = 1.7V to 3.6V</fs>   
</WRAP>
  * ICC = 0.65µA Operating Current
  * -40° C to +85°C Temperature Range
  * Device Address Options :1001 010x and 1001 011x
\\
===== LIS2DTW12 Features ====
<WRAP left 600px  :en>
  * Ultra-low power consumption: 50 nA in power-down mode, below 1 µA in active low-power mode
  * Very low noise: down to 1.3 mg RMS in low-power mode
  * 0.8 °C (typ. accuracy) embedded temperature sensor
  * Multiple operating modes with multiple bandwidth
  * Android stationary detection, motion detectio
  * Supply voltage, 1.62 V to 3.6 V
</WRAP>   
  *  ±2g/±4g/±8g/±16g full scale
  * High-speed I²C/SPI digital output interface
  * Single data conversion on demand
  * 16-bit accelerometer data output
  * 12-bit temperature data output
  *10000 g high shock survivability
\\
\\
===== BME680 Features ====
<WRAP left 600px  :en> 
  * Supply voltage
         * VDD main supply voltage range: 1.71 V to 3.6 
         * VDDIO interface voltage range: 1.2 V to 3.6 V
  * <fs medium>Current consumption</fs> 
            * 3.1 µA at 1 Hz pressure and temperature
            * 3.7 µA at 1 Hz humidity, pressure and temperature
            * 0.09‒12 mA for p/h/T/gas depending on operation mode
            * 0.15 µA in sleep mode
</WRAP>
  * Digital interface: I²C (up to 3.4 MHz) and SPI (3 and 4 wire, up to 10 MHz)
  * Operating range -40‒+85 °C, 0‒100% r.H., 300‒1100 hPa
  * RMS Noise 0.12 Pa, equiv. to 1.7 cm
  * Offset temperature coefficient ±1.3 Pa/K, equiv. to ±10.9 cm at 1 °C temperature change
\\
===== SI7006 Features ====
<WRAP left 600px  :en>
  * Precision Relative Humidity Sensor
      * ± 5% RH (max), 0–90% RH
  * High Accuracy Temperature Sensor
    * ±1 °C (max), –10 to 85 °C
  * 0 to 100% RH operating range
  * –40 to +125 °C operating range
  * Low Power Consumption
    * 150 µA active current
    * 60 nA standby current
</WRAP>
  * Wide operating voltage (1.9 to 3.6 V)
  * I2C host interface
  * Integrated on-chip heater
  * Excellent long term stability
  * Optional factory-installed cover
  * Low-profile
  * Protection during reflow
  * Excludes liquids and particulates
\\
\\

=====Board Pinout=====
n-PRO-3DP is a **PERIPHERAL** board with four Hirose DF30-series 60-pin low profile connectors at top side, following the [[nblocks:nproformfactor|n-Blocks PRO form factor]].\\


<WRAP centeralign>{{:nblocks:n-pro-s1-01.jpg?400|}}</WRAP>





=====Related articles in this Wiki=====
  *[[start]]

{{tag> RF CPU nblock BLE  nsensorRF}}