Table of Contents
n-PRO-SEN1
n-PRO-SEN1
n-PRO-s1
| License | GPL 2.0 |
| Status | Tested |
| Buy at: | |
| Categories | |
| Hardware repo | Bitbucket |
| Firmware repo |
n-PRO-S1 is an environmental sensor board, in the standard n-Blocks pro form factor.
Overview
n-PRO-S1 is designed around the MAX44009 ambient light sensor, the LIS2DTW12 motion and temperature sensor, the BME860 atmospheric pressure and VOC sensor and the SI7006 Temperature/Humidity Sensor.The board can be used to monitor the environment conditions, and store or transmit the data to a remote system for further processing. The n-PRO PERIPHERAL connectors pinout allow n-PRO-S1 to be connected to any n-PRO HOST board to add additional functionality. It is simple to just plug and get started with sensor applications immediately.
MAX44009 Features
- Wide 0.045 Lux to 188,000 Lux Range
- Small, 2mm x 2mm x 0.6mm UTDFN-Opto
- VCC = 1.7V to 3.6V</fs>
- ICC = 0.65µA Operating Current
- -40° C to +85°C Temperature Range
- Device Address Options :1001 010x and 1001 011x
LIS2DTW12 Features
- Ultra-low power consumption: 50 nA in power-down mode, below 1 µA in active low-power mode
- Very low noise: down to 1.3 mg RMS in low-power mode
- 0.8 °C (typ. accuracy) embedded temperature sensor
- Multiple operating modes with multiple bandwidth
- Android stationary detection, motion detectio
- Supply voltage, 1.62 V to 3.6 V
- ±2g/±4g/±8g/±16g full scale
- High-speed I²C/SPI digital output interface
- Single data conversion on demand
- 16-bit accelerometer data output
- 12-bit temperature data output
- 10000 g high shock survivability
BME680 Features
- Supply voltage
- VDD main supply voltage range: 1.71 V to 3.6
- VDDIO interface voltage range: 1.2 V to 3.6 V
- Current consumption
- 3.1 µA at 1 Hz pressure and temperature
- 3.7 µA at 1 Hz humidity, pressure and temperature
- 0.09‒12 mA for p/h/T/gas depending on operation mode
- 0.15 µA in sleep mode
- Digital interface: I²C (up to 3.4 MHz) and SPI (3 and 4 wire, up to 10 MHz)
- Operating range -40‒+85 °C, 0‒100% r.H., 300‒1100 hPa
- RMS Noise 0.12 Pa, equiv. to 1.7 cm
- Offset temperature coefficient ±1.3 Pa/K, equiv. to ±10.9 cm at 1 °C temperature change
SI7006 Features
- Precision Relative Humidity Sensor
- ± 5% RH (max), 0–90% RH
- High Accuracy Temperature Sensor
- ±1 °C (max), –10 to 85 °C
- 0 to 100% RH operating range
- –40 to +125 °C operating range
- Low Power Consumption
- 150 µA active current
- 60 nA standby current
- Wide operating voltage (1.9 to 3.6 V)
- I2C host interface
- Integrated on-chip heater
- Excellent long term stability
- Optional factory-installed cover
- Low-profile
- Protection during reflow
- Excludes liquids and particulates
Board Pinout
n-PRO-3DP is a PERIPHERAL board with four Hirose DF30-series 60-pin low profile connectors at top side, following the n-Blocks PRO form factor.
